Fireproof 13A Wall Power Socket – 8mm Stainless Steel Panel, UK/EU/US/FR Universal, Single & Double Gang

13A wall power sockets with 8mm stainless steel face plate and flame-retardant internal components for residential and commercial installation. The stainless steel face plate provides a premium, corrosion-resistant finish suitable for kitchens, bathrooms (outside the exclusion zone), and commercial environments where standard plastic face plates are inadequate. Available in UK (Type G), EU (Type F/Schuko), US (Type A/B), and French (Type E) plug standards to cover the major global socket formats. Single gang (one socket) and double gang (two sockets) configurations.

Key Specifications

• Current Rating: 13A
• Voltage: 250V AC
• Face Plate: 8mm stainless steel (304 grade)
• Internal Material: Flame-retardant PC/ABS, UL94 V-0
• Plug Standards: UK Type G, EU Type F (Schuko), US Type A/B, French Type E (select above)
• Gang: Single (1 socket) or Double (2 sockets) (select above)
• Mount: Flush mount (requires 86-type back box)
• Terminal: Screw clamp, accepts 1.5–4mm² wire

UK vs EU vs US vs FR Socket Standards

• UK Type G (BS 1363): 3-pin rectangular blade. 13A fused plug. Standard in UK, Ireland, Hong Kong, Singapore, Malaysia. The only major socket standard with a fuse in the plug.
• EU Type F (Schuko, CEE 7/4): 2 round pins + 2 earth clips. 16A. Standard in Germany, Austria, Netherlands, and most of continental Europe. Accepts Type C plugs.
• US Type A/B (NEMA 5-15): 2 flat blades + round earth pin. 15A. Standard in USA, Canada, Mexico, Japan, and many countries in the Americas.
• French Type E (NF C 61-314): 2 round pins + earth socket pin. 16A. Standard in France, Belgium, Poland, Czech Republic, Slovakia. Visually similar to Schuko but not interchangeable — the earth connection is a pin in the socket, not clips on the sides.

Frequently Asked Questions

What back box is required for this socket?

This socket requires a standard 86-type (86×86mm) recessed wall back box. The socket mounts to the back box using two M4 screws. Back box depth: 35–40mm standard; 50mm deep box recommended if multiple cables enter the same box. The stainless steel face plate overlaps the back box opening and sits flush against the wall surface.

Does this socket require an RCD?

In most jurisdictions, sockets in kitchens, bathrooms, garages, and outdoor locations must be protected by a 30mA RCD (residual current device). Check local electrical regulations — requirements vary by country and installation location. The socket itself does not include integrated RCD protection; install an RCD at the distribution board or use a socket with integrated RCD if required.

What wire gauge should I use for a 13A socket circuit?

Use 2.5mm² (14AWG) cable for 13A socket circuits — this is the standard for ring main circuits in UK wiring and equivalent circuits in other standards. For radial circuits (single socket on a dedicated circuit), 2.5mm² is also standard. The socket’s screw terminals accept 1.5–4mm² wire.

Is stainless steel face plate suitable for bathroom installation?

Stainless steel face plates are suitable for bathroom zones 2 and 3 (outside the exclusion zone around the bath/shower) where IP44 or higher is required. Verify the socket’s IP rating — standard wall sockets are typically IP20 (not splash-proof). For bathroom zone 2 (within 0.6m of the bath/shower), use IP44-rated sockets specifically designed for bathroom installation.

Typical Applications

• Kitchen: Worktop sockets, appliance power points
• Commercial: Office and retail power points requiring a premium finish
• Hospitality: Hotel room and restaurant power points
• Residential renovation: Upgrading standard plastic sockets to stainless steel finish
• Industrial offices: Power points in environments where plastic face plates are prone to damage

Package Contents

Wall power socket with stainless steel face plate (plug standard and gang configuration as selected). Mounting screws included. Back box not included.